powermatic

  1. MrAudio815

    PowerMatic 2000 Reliable casters???

    Hey Guys,:wsmile: It's was nice to meet you all today at Klingspors!!!:icon_thum Guess what I bought today? :eusa_danc A PM2000 and love it so far. It is very Heavy and well built. I love the ease of changing the blade and the riving knife. The hand wheels are not as easy as the Saw stop...
  2. MrAudio815

    Sawstop or Powermatic? And what all about riving knives

    Who's better than who? :dontknow: I'm interested in your Knowledge & expertise. I would like to buy one or the other, but can't decide who's better? And the riving knife on the Saw stop how it follows the blade? Good thing or bad? What's in you garage? Matthew & Rachel Custom Home...
  3. mburke911

    on CL: Brand New PowerMatic PM2000 in Greensboro

    Powermatic PM2000, 5HP 1PH Table Saw w/ 50" Accu-Fence & Rout-R-Lift. Please email me if interested. http://greensboro.craigslist.org/tls/547149803.html
  4. T

    Help with Powermatic PJ-882 Review

    I have a Powermatic PJ882, 8" parallelogram jointer in the shop and am in the process of writing a review on it. I thought I'd ask what the members here wanted to know about this type of machine to see if that differes from what I think is important. Right now it has the straight knife...
  5. Adjustable Feet

    Adjustable Feet

    Adjustable feet makes it easy to accommodate uneven floors.
  6. Legs Folded Up

    Legs Folded Up

    To fold the legs up, remove the Locking Knobs and swing the legs assembly to the right.
  7. Leg Hinge & Locking Knob

    Leg Hinge & Locking Knob

    The 5/16'' hinge bolt is attached to 1-1/4'' angle iron used for mounting out-feed table. Locking knob is a lawnmower handle replacement knob, epoxied to 5/16'' threaded rod. Keywords: PowerMatic 64A Fold-up Outfeed Table Tablesaw Support Leg
  8. Fold-up Support Legs

    Fold-up Support Legs

    Outboard support legs are required to accommodate additional weight of extension table, accessory drawer, and outfeed table. Remove two locking screws to fold the legs up to move the saw.
  9. KC7CN

    PowerMatic 64A Outfeed Table - Completed

    PowerMatic 64A Fold-Down Out-feed Table. This project took a lot more time than I thought it would! You can see more pictures, with additional details, in my photo album. http://www.ncwoodworker.net/pp/showgallery.php?cat=1012 It's amazing how many ways you can build an out-feed table...
  10. Miter Gauge Dado Alignment Jig

    Miter Gauge Dado Alignment Jig

    This jig is used to align the dado slots to the table saw miter track. The jig consists of a 2-3/4" x 45" piece of hardwood. Plane thickness to 3/4"; for snug fit in the miter track. A 21" x 1-1/4" notch on one end is required to clear the template.
  11. Miter Gauge T-Track

    Miter Gauge T-Track

    Additional 5/8'' support blocks required under miter T-track.
  12. PowerMatic 64A Outfeed Table

    PowerMatic 64A Outfeed Table

    Note how the extra 5'' of miter track is utilized with the cross-cut sled.
  13. PowerMatic 64A Outfeed Table

    PowerMatic 64A Outfeed Table

    This photograph illustrates how much safer it will be to use this large crosscut sled with the outfeed table.
  14. Motor Access Hole Template

    Motor Access Hole Template

    The age-old tradition of trial-and-error was used to determine size and location of the motor access hole. The template was used to route the hole.
  15. Setup for Cutting the  Miter Slots.

    Setup for Cutting the Miter Slots.

    This picture was taken after-the-fact, so you need to use your imagination to understand how this works. Install the table on temporary riser blocks (this is necessary to allow clearance for the router bit between the table saw and extension table). Temporarily place the Aluminum T-Track in...
  16. Miter Gauge Template

    Miter Gauge Template

    Location of the two T-slot Aluminum Miter gauge tracks must be dead on. The gap between the miter bar and the track is 0.005" on either side. The template was made for use with a top-bearing 1/4' height template bit.
  17. Motor Access Hole

    Motor Access Hole

    Table saw blade fully retracted, tilted to 45 degrees.
  18. Table Support Detail

    Table Support Detail

    Angle iron attached to mounting block with 1/4'' bolt and T-nut. Mounting blocks are screwed, and glued, to table. Top is 5/8'' particle board covered with laminate. Underside of table is reinforced with 5/8'' x 1-1/2'' particle board.
  19. Angle Iron Table Mount

    Angle Iron Table Mount

    1-1/4'' x 3/16'' heavy-duty angle iron table support. Short pieces of angle iron are used to attach the table support to existing holes in the table saw. Note shims (washers) between angle iron and table top assembly.
  20. Motor

    Motor

    Closeup of motor in table top clearance hole.

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top