part

  1. johnpipe108

    Router-table sub-plate aids small part shaping

    When shaping small parts on the router table, the large center hole in the router-table mounting plate is problematic. To get around this, I drilled a small bit-clearance hole in a scrap piece (here I used 1/4" MDF) and temporarily affixed this "sub-plate" to the table with double-stick tape...
  2. DaveO

    An experiment part deux

    In a continuing effort to think outside the blank, and to reduce my scrap accumulation, I decided to try another pen blank. I had the shop all set up to cut very thin strips of wood for a run of my free-form cutting boards and I said why not cut a few extra while I have everything dialed in. So...
  3. mkepke

    Why You Need a Shop Crane, Part 2

    Because you might have this in the back of your vehicle. CAUTION: this is not an approved shipping method. OK, shop crane, come-along, ramps..everything but the kitchen sink ! TIP: A 14' length of 8/4 oak makes a *fine* brace for the come-along. Just wedge it across the door opening ...
  4. C

    Chessboard WIP - Part 2

    Well, I finally got some more time in the shop. Here are some recent pictures. More in my gallery Still have much sanding to do. Here is the top Side view Here is where the drawer will go to hold the pieces. Thanks for looking. All that's left to do is make the drawer and compartments...
  5. SteveColes

    New Policy statement - Part two

    Ok, here is my second draft. I hope it is more clear about why and what to do. Feedback please
  6. SteveColes

    Floating Menu in Test part 2

    I've Incorporated all the changes and fixes from the last the review. I hope :lol: . I also added all the stuff that was missing from before. The only exception is the frapper map. At this point I can't make the view your photos work like I would like and the same goes for the searches.( I am...
  7. jmauldin

    Tung & Linseed oils - part 2

    Here's a follow-up to the first article. I do have a related question. What is boiled linseed oil and how does it compare to 'regular' linseed oil. Also, I am building a children's picnic table out of pine or cedar. I have been told to finish it in linseed oil, but don't know if it should be...
  8. C

    Jewelry Box Part II - Feedback/ideas

    I have completed the box for my oldest daughter in purpleheart with padauk top panel. I intended to route the bottom edge to form feet on the outsides but test runs showed way too much tearout on the purpleheart, even with VERY light passes. Pics are attached...I think the box looks to...well...
  9. DaveO

    DaveO's wood deal part 2

    Well my buddy arrived yesterday with a truck of wood for me to sell. It wasn't as much as I had originally thought due to very picky grading (he tried to send only the best boards). I ended up with 150 BF of 9" or wider 4/4 Red Oak. 135 BF of 10" or wider 4/4 Walnut and a 125 BF of 12/4 Red...
  10. DaveO

    Tea house WIP part deux

    Well, another two days have past and I got a little more done on my Tea house project. Most of the deck flooring is complete. I need some more boards to complete it, because 6 of the 22 boards that we got were unaccepatable (I didn't pick out the lumber myself). I spent today cleaning up the...
  11. mshel

    Just about done part daux

    Reference my original thread to see the latest acquisition. Last post in the thread. http://www.ncwoodworker.net/forums/showthread.php?t=2200 Mike
  12. Arcrist

    Part Problem

    Maybe Im just an idiot but im trying to order the part for my broken saw and more problems stand in my way. This is a message from the supplier of the part. Can anyone make sense of how to order?? "Andy 422 16 067 0002 lock lever $16.07 ea In stock at this time Is that all that is broken...
  13. Handturnedbowls

    First turned bowl part 2

    Re: First turned bowl There are rare cases when a person is exposed to it first hand it triggers the gene to life. My wife, bless her heart, was the first to notice. She asked me why I started wearing sweat shirts and loose clothing all the time. I told her it allowed curls and chips to fall...
  14. DaveO

    Rt in progress pics part duex

    I had hoped to get farther along this weekend, but with a daughter getting over strep throat and a wife who just got it, my time was limited. I managed to get the top glued up and attached, cut the miter and t-track slots, and started on the fence. The fence isn't glued/screwed, I just put it...
  15. DaveO

    Quadruplets part deux

    OK, I sanded my arms off today and this is the result. Not finished, but wiped down with MS. The pivot pin set-up worked like a charm, so far I don't believe that I have screwed anything up on this project...but I haven't got to the finish yet, so there is still time. These babies are baby butt...
  16. SteveColes

    FAQ and How To's - Part deux

    If I understand what most people where suggesting, I just set it up. Please take a look and let me know if there are any issues. Please note that anybody can create a FAQ or how too, but Unless you are a Mod or admin it will go to the Moderation Queue. All of you willbe notified that something...
  17. Monty

    Mmm.... Dovetails - Part Deux

    Scrap walnut. Wiped on some mineral spirits to show the color. Not as much contrast with the end-grain as I was expecting... This is one foot wide. What do you guys think about the number and spacing of the pins? Oh yeah, almost forgot - I tried a little "experimental design...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top