live
-
Live edge coffee table
Figures live edge maple slab on cherry base. Donated to FCA to help raise money at a silent auction.- BallashWoodworking
- Media item
- coffee edge live table
- Comments: 0
- Category: Member Galleries
-
live edge coffee table close up
After 5 layers of tung oil. Donation project to local school for silent auction.- BallashWoodworking
- Media item
- coffee edge live table
- Comments: 0
- Category: Member Galleries
-
Live Edge Garden Bench
Live Edge Garden Bench built out of scrap lumber from a mill. Pulled all the bark off, pressure washed the wood. Hand planed the top to almost the same thickness. Joinery was through tenons. For build along photos visit my facebook page- www.facebook.com/asliceofwood- Timmy
- Media item
- bench edge flower garden live rustic seat
- Comments: 0
- Category: Furniture Projects
-
Live Edge Garden Bench
Live Edge Garden Bench built out of scrap lumber from a mill. Pulled all the bark off, pressure washed the wood. Hand planed the top to almost the same thickness. Joinery was through tenons. For build along photos visit my facebook page- www.facebook.com/asliceofwood- Timmy
- Media item
- bench edge flower garden live rustic seat
- Comments: 0
- Category: Furniture Projects
-
Live Edge Garden Bench
Live Edge Garden Bench built out of scrap lumber from a mill. Pulled all the bark off, pressure washed the wood. Hand planed the top to almost the same thickness. Joinery was through tenons. For build along photos visit my facebook page- www.facebook.com/asliceofwood- Timmy
- Media item
- bench edge flower garden live rustic seat
- Comments: 0
- Category: Furniture Projects
-
Remove bark from live edge without damaging edge
I have a piece of white oak 24" x 48" x 2" with a live edge and most of the bark still attached. I have the piece surfaced and would like to use it as a table top. How do i remove the bark from the live edge without damaging the wood? Also, how is the best way to sand and leave the natural...- cyclopentadiene
- Thread
- damaging edge live remove
- Replies: 6
- Forum: "How To" Forum
-
-
-
-
-
-
-
B
Looking for large Live Edge Wood Slabs
We have a customer wanting a few things made from live edge wood. Preferably Walnut, Maple or Cherry. We need either a large piece or a few smaller pieces that can be made into a desk top, small printer table and chair back. It needs to be fairly thick 1-2". Any help where I can find some that...- blueridgewoodworking
- Thread
- edge large live slabs wood
- Replies: 3
- Forum: Wood
-
Which gouge for dressing a live edge slab?
I have never done any carving but I have seen some nicely dressed live edge slabs that appear to have been done by a gouge. I will be working the live edge of a red oak slab soon and I think I will need a gouge; any suggestions on what size, type, brand, etc that I should seek out? Thanks- kooshball
- Thread
- dressing edge gouge live slab
- Replies: 15
- Forum: Hand Tools and their Use
-
-
-
-
Need Assistance - Delta Lathe Live End
I need this groups assistance. I have a Delta Midi (Mini) Lathe that has a live tail end that is not spinning freely. I believe a bearing has gone out due to the LOUD squeal that comes from it sometimes. Where would I find a replacement/ upgrade to the original? :notworthy:- Leviblue
- Thread
- assistance delta end lathe live
- Replies: 9
- Forum: General Woodworking
-
need chuck and live center?
Sorry if this is put in wrong thread, and long time no see: I was in this group before and then life got busy... I need a Jacobs chuck, screw on, 3/4" and 16 TPI, 5-20 mm capacity. I also need a live head, 1 MT, preferably the kind with teeth and a sprung point. I cannot seem to find them in...- Flootsie
- Thread
- center chuck live
- Replies: 1
- Forum: Woodturning
-
T
Looking for a source for quartersawn live oak
Hey all, I got 1 board of live oak a while ago out of a guy's back pasture pile... I finally got around to cleaning it up and like what I am seeing so far..... Unfortunately, I don't think I can get any more from him... It was mostly rotten and buggy... and he got a real day job and started...
Premier Sponsor
Our Sponsors
LATEST FOR SALE LISTINGS
-
-
Graco 395 FinishPro air assisted airless sprayer for sale
- Started by RobH
- Replies: 1
-
-
-