jig

  1. IMG_08962

    IMG_08962

  2. IMG_08443

    IMG_08443

  3. IMG_08432

    IMG_08432

  4. IMG_08422

    IMG_08422

  5. Small Circle Cutting Jig for bench top Bandsaw

    Small Circle Cutting Jig for bench top Bandsaw

    Small Circle Cutting Jig for bench top Bandsaw
  6. Small Circle Cutting Jig for bench top Bandsaw

    Small Circle Cutting Jig for bench top Bandsaw

    Small Circle Cutting Jig for bench top Bandsaw
  7. Small Circle Cutting Jig for bench top Bandsaw

    Small Circle Cutting Jig for bench top Bandsaw

    Small Circle Cutting Jig for bench top Bandsaw
  8. Small Circle Cutting Jig for bench top Bandsaw

    Small Circle Cutting Jig for bench top Bandsaw

    Small Circle Cutting Jig for bench top Bandsaw
  9. DSC00396

    DSC00396

  10. DSC00394

    DSC00394

  11. KC7CN

    Advanced Box Joint Jig - new to me!

    It's been a long time since I have posted anything - please accept my apology if this has already been posted. I like box/finger joints and have always been fascinated by the variety of jigs to make them! I recently ran across this Advanced Box Joint Jig while searching Google, and noticed a...
  12. bluedawg76

    tenon jig

    for those who saw my new mortising jig for the router, here's its companion the tenon jig for the tablesaw. the plans were from a shopnotes book. It uses barrel bolts/wing nuts to act as stops for the sliding top so that you can cut each cheek w/o removing the board. View image in gallery...
  13. bluedawg76

    router mortising jig

    in preparation for a number of mortises I need to make, I took the plunge (pun intended) and built a mortising jig for the router. Til now, I've either done them blind on the router table which is a bit of pain to setup or just chopped them with a chisel/mallet. On a recent post on routers and...
  14. T

    Router jig for cutting bench dog holes?

    Afternoon all, I remember reading an article/watching a video where a guy used a jig of some sort with a router, to get "dead-on spacing/accuracy" for these but for the life of me, cannot seem to remember where or who did it? Anyone here have any experience with such a thing? I am planing to...
  15. S

    Using a Porter-Cable 4212 Jig with different routers

    I have a PC 4212 dovetail - fingerjoint jig. It comes with bushings for a PC router. Anybody use one with a different router. What do you do about bushings. The instructions say you must use a base that holds the P-C bushings. I have a Bosch 1617EVS and a larger Craftsman pro router. Can...
  16. Gary_C

    Flush cut jig for router

    I'm wondering if any of you guys have made a jig for steadying a router when using a flush cut bit. I'm a complete newbie at woodworking and saw an episode of Woodsmith that showed this jig and think it would work for my current problem. My first read wood project is a set of nesting end...
  17. gator

    Alan's Jig

    Mods - If this is not appropriate please delete or move. Saw this thread by Alan in Little Washington on another forum. Thought everyone here might find it interesting. http://www.woodworkslive.com/index.php/topic,11625.0.html George
  18. J

    Industrial Jig Saw, Yates American Y-3 - $300 (Apex

    NOT MINEraleigh craigslist > for sale / wanted > tools please flag with care: [?] miscategorized prohibited spam/overpost best of craigslist Avoid scams and fraud by dealing locally! Beware any deal involving Western Union, Moneygram, wire transfer, cashier check, money order, shipping...
  19. Quickset Knife Jig

    Quickset Knife Jig

    Quickset Jointer/Planer Knife Setup Jig
  20. CrealBilly

    Taper Jig

    Looking for a good taper jig for the TS - what's your experiences? Home made is better than store bought? Thanks

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top