grinding

  1. Ed Fasano

    Bowl Gouge Grinding Help

    I have a sense that I know what I’m doing wrong, but I’d be most grateful for some experienced guidance. My efforts to put a 50-degree bevel on a new bowl gouge have yielded what I’ll call a scalloped sweep, wherein the bevel is something other than uniform at the leading edge. It almost as if...
  2. IMG_08982

    IMG_08982

    • eyekode
    • Media item
    • gouge grinding jig
    • Comments: 0
    • Category: Tools & Equipment Photos
  3. IMG_08972

    IMG_08972

    • eyekode
    • Media item
    • gouge grinding jig
    • Comments: 0
    • Category: Tools & Equipment Photos
  4. IMG_08962

    IMG_08962

    • eyekode
    • Media item
    • gouge grinding jig
    • Comments: 0
    • Category: Tools & Equipment Photos
  5. For mama's kitchen

    For mama's kitchen

    Cherry Grinding Mill
    • Tommy Smith
    • Media item
    • grinding mill
    • Comments: 0
    • Category: Turning - 2012 Calendar Contest
  6. Tommy Smith

    Grinding Mill

    Since this was the 1st I'v made I stayed with a simple design. Cherry, 9 1/2" tall, 2 3/4" wide. Still needs a finish and I'm thinking of MinWax Wipe on Poly. The mechanism is made from ceramic and is supposed to crush pepper, salt or herbs so you can use it anyway you want. Thanks for looking.
  7. D

    Grinding Jig Help

    Still getting started in my quest of turning and wanted advice and opinions from "the collective" on experiences and recommendations for grinding jigs. Whatta' you like? What's a waste? Thanks friends.
  8. Grinding Station

    Grinding Station

    • Nate Davey
    • Media item
    • grinding station
    • Comments: 0
    • Category: Member Galleries
  9. eyekode

    Thompson Tools bowl gouge and grinding setup

    I bought my first bowl gouge last week and I finally got a chance to put a handle on it. It is a 1/2" Thompson V shaped bowl gouge. I don't have much experience with lathes or lathe tools so take all of this with a grain of salt or too. Shipping was great. It arrived before I expected it. And...
    • eyekode
    • Thread
    • bowl gouge grinding setup thompson tools
    • Replies: 4
    • Forum: Woodturning
  10. CatButler

    Grinding PVC

    Hi, I found a great craft for my kids' Y -guides tribes to make Native American flutes from PVC pipe. Do do this, I need to flatten about 1.5 inch section of the pipe. The web page I found uses a file and sandpaper, which I certainly have, but I need to knock out 16 of these things, so I'm...
  11. froglips

    Gloat: Blacksmith Pedal Grinding Wheel

    I was at an auction the other night, and what did my bidding card bring home? A little ole grinding wheel! The base is rock solid and the wheel is not cracked. Thanks to Woodartz for helping me move it. For those who wonder, tis sitting center in my living room, where it rightfully...
  12. G

    Grinding turning tools

    On one of the other threads: "Get a grinder from tractor supply for $39. and make the wheels spin backwards, much easier to grind free hand" Is grinding with the wheels spinning backwards a good process? I have always ground with the grinder set up in normal mode with a wolverine type jig, but...
  13. Phil S

    FREE Grinding wheels

    And the are gone I had to replace my old grinder so I bought an 8 inch slow-speed. It came with fine and medium grit white friable wheels. These have a 7/8 bore sleeved down to a standard 5/8, so they are usable on most grinders. However I use the Oneway wheel balancer and it requires one...
  14. NCTurner

    Oneway Wolverine grinding jig

    This is going to go somewhat cheap and w/o much action..it is misspelled as One-Way. Good luck. I am no longer bidding. Wolverine P.S. If someone is going to bid on it please let everyone know so that you aren't bidding against each other.
  15. S

    Wolverine grinding jig

    I am in the market for a sharpening system for lathe tools and was wondering about the Wolverine system. I know there are some expensive systems on the market but the Wolverine seems to be pretty easy to set up and use (just from reading the ads). I wonder if anyone has one and what you think...
  16. Badabing

    New grinding wheel problem

    Need some help :eusa_doh: I have an 8'' variable speed bench grinder. I'm using it mostly to sharpen lathe tools. It came with a 60 grit gray wheel and a wire wheel. I thought I'd replace the wire wheel with a white aluminum oxide wheel so today I got a Camel brand 8'' white AO wheel...
  17. Handturnedbowls

    Ceramic Grinding wheel

    I recently got a set of 3 ceramic grinding stones. I didnt realize what I had until I looked up the number from Norton. Their signature color is purple. I have never found a wheel that cuts as good as this, with virtually no heat generation. Now I dress my tools using this wheel exclusively...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top