gouge

  1. Ed Fasano

    Bowl Gouge Grinding Help

    I have a sense that I know what I’m doing wrong, but I’d be most grateful for some experienced guidance. My efforts to put a 50-degree bevel on a new bowl gouge have yielded what I’ll call a scalloped sweep, wherein the bevel is something other than uniform at the leading edge. It almost as if...
  2. IMG_08982

    IMG_08982

    • eyekode
    • Media item
    • gouge grinding jig
    • Comments: 0
    • Category: Tools & Equipment Photos
  3. IMG_08972

    IMG_08972

    • eyekode
    • Media item
    • gouge grinding jig
    • Comments: 0
    • Category: Tools & Equipment Photos
  4. IMG_08962

    IMG_08962

    • eyekode
    • Media item
    • gouge grinding jig
    • Comments: 0
    • Category: Tools & Equipment Photos
  5. D

    Any tips for sharpening bowl gouge?

    I made a jig sharpen my roughing gouge, just an adjustable rod coming from under the bench grinder with a little cup for the butt of the tool. Obviously this is only good for sharpening a square edge, and won't work for the rounded edge of a bowl gouge (not sure correct terminology). If anyone...
  6. NCTurner

    Ebay JERRY GLASER WOODTURNING BOWL GOUGE

    http://www.ebay.com/itm/JERRY-GLASER-WOODTURNING-BOWL-GOUGE-LITTLE-USE-GREAT-CONDITION-/170699208881?pt=LH_DefaultDomain_0&hash=item27be7738b1
  7. kooshball

    Which gouge for dressing a live edge slab?

    I have never done any carving but I have seen some nicely dressed live edge slabs that appear to have been done by a gouge. I will be working the live edge of a red oak slab soon and I think I will need a gouge; any suggestions on what size, type, brand, etc that I should seek out? Thanks
  8. scsmith42

    Roughing gouge question

    Now that I've joined "the dark side", some of my first projects will be making some tools for the lathe. I have a basic set, but I'd like to make something more substantial. I have turned my first handle and installed a brass ferule that I turned down from a piece of brass pipe. The handle is...
  9. 69CG8441

    69CG8441

    • eyekode
    • Media item
    • gouge
    • Comments: 0
    • Category: Member Galleries
  10. 69CG8439

    69CG8439

    • eyekode
    • Media item
    • gouge
    • Comments: 0
    • Category: Member Galleries
  11. eyekode

    Thompson Tools bowl gouge and grinding setup

    I bought my first bowl gouge last week and I finally got a chance to put a handle on it. It is a 1/2" Thompson V shaped bowl gouge. I don't have much experience with lathes or lathe tools so take all of this with a grain of salt or too. Shipping was great. It arrived before I expected it. And...
    • eyekode
    • Thread
    • bowl gouge grinding setup thompson tools
    • Replies: 4
    • Forum: Woodturning
  12. Flute Maker

    Gouge for Carving ? Maybe Turning

    I have a 1 inch used Buck Bros gouge that one of my sons gave me for carving. Could a gouge of this type be used for turning also? I didn't see how to post a pic here I will in the photo thread Thanks Mike
  13. H

    Chatter with bowl gouge? Inside roughing cut

    All: A relatively novice turner here - at least as far as bowls go. I likely have more "spare" pen parts than most of you, as least as a ratio with the number of pens I have completed (5?). I am trying my hand at some maple bowls with a natural edge. One piece is about 10" in diameter and...
    • Henry W
    • Thread
    • bowl chatter cut gouge inside roughing
    • Replies: 20
    • Forum: Woodturning
  14. CarvedTones

    customizing small carving gouge handles

    I just ordered a few Warren gouge blades. You can see them on the lower left of this page: http://www.warrencutlery.com/indexb.htm I have one of the little gouges on the lower right, the ever popular 3/4" fish tail 4 sweep, and while it is one of my favorites, it is not just a handled version of...
  15. CarvedTones

    Is this gouge suitable for mallet work?

    http://www.grizzly.com/products/H0514 I have been offered one in trade for my WeCheer listed in the classifieds and the current owner has only used it a couple of times by hand.
  16. NCTurner

    ? 3/4" Bowl Gouge

    So, I stopped by Klingspor today to take advantage of their 20% off sale, and picked up a Crown 3/4" Bowl gouge. I got this suker home and started looking at it and keep thinking this sucker is BIG:eek:. Question is, is it to big? Anyone use one of these monsters?
  17. mbeach

    Looking for a bowl gouge

    I am looking for a decent cheap (used or new) bowl gouge. Anyone have one they would like to sell or know where to get one? Thanks Michael
  18. WoodWrangler

    Quick, but Effective Gouge Shelf

    Well, the Turn & Learn is Tuesday at mi casa and my lathe tools had no place to live since parting with the Delta and it's great storage system underneath! That just wouldn't do ... So between time working on the Maloof chair, I built this extremely simple and not-so-elegant shelf for the gouges.
  19. Splinter

    Bowl Gouge

    I'm looking for recommendations for a Bowl Gouge to use with my Delta Midi lathe. So..... Which gouge should I buy....why? Should I get one with the Ellsworth grind....why? What size 1/2" or 5/8....why" Any other suggestions welcome. Thanks
  20. WoodWrangler

    Great Price on Lathe 8pc Gouge Set from WC

    Great deal on these gouges from Woodcraft .... I believe they are branded as "Pinnacle" brand. Turner's Set of 8 set normally $215, on sale for $150 with a $20 gift card ... so nearly half price! http://www.woodcraft.com/family.aspx?FamilyID=5238 Coupon Code: 10161 (for gift card)

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top