fixture

Box Joint Jig

Box joint jig
- Acelectric
- Media item
- Mar 9, 2013
- box finger fixture jig joint
- Comments: 0
- Category: Member Galleries
Box Joint Jig

Box joint
- Acelectric
- Media item
- Mar 9, 2013
- box finger fixture jig joint
- Comments: 0
- Category: Member Galleries
Box Joint Jig

Base, rear fence, rear sub-fence, front fence, runners
- Acelectric
- Media item
- Mar 9, 2013
- box finger fixture jig joint
- Comments: 0
- Category: Member Galleries
Box Joint Jig

Box joint jig base
- Acelectric
- Media item
- Mar 9, 2013
- box finger fixture jig joint
- Comments: 0
- Category: Member Galleries
Paint filter - spray gun holder

Hole in top is 4 3/4" dia.
- Bill Clemmons
- Media item
- Nov 3, 2011
- filter finishing fixture gun spray
- Comments: 0
- Album: Paint filter - spray gun holder
Paint filter - spray gun holder

Shelf pivots on short pieces of 1/8" dowels driven in from sides.
- Bill Clemmons
- Media item
- Nov 3, 2011
- filter finishing fixture gun spray
- Comments: 0
- Album: Paint filter - spray gun holder
Paint filter - spray gun holder

Low wall in front is 2" high.
- Bill Clemmons
- Media item
- Nov 3, 2011
- filter finishing fixture gun spray
- Comments: 0
- Album: Paint filter - spray gun holder
Paint filter - spray gun holder

Sized to fit my gravity feed gun.
- Bill Clemmons
- Media item
- Nov 3, 2011
- filter finishing fixture gun spray
- Comments: 0
- Album: Paint filter - spray gun holder
Paint filter - spray gun holder

Top of flip up shelf is 5" from bottom of base.
- Bill Clemmons
- Media item
- Nov 3, 2011
- filter finishing fixture gun spray
- Comments: 0
- Album: Paint filter - spray gun holder
Paint filter - spray gun holder

7 1/2w x 7d x 19h. Made from 1/2" plywood.
- Bill Clemmons
- Media item
- Nov 3, 2011
- filter finishing fixture gun spray
- Comments: 0
- Album: Paint filter - spray gun holder
Humming light fixture

I hung some light fixtures this weekend. They are two-light four-foot T-8 fixtures, from Home Depot. In total, I have six lights (well, so far...). Four lights are on circuit A, two are on circuit B. Let's ignore the lights on circuit B. To have some better control over the lights, I mounted...
- Bas
- Thread
- Nov 1, 2009
- fixture humming light
- Replies: 10
- Forum: Workshop Discussion
Jig & Fixture Value Pack - Hartville Tool

Are you looking for a good buy on T-Track and accessories? Check out Hartville Tool.
- Splinter
- Thread
- Jul 19, 2006
- fixture hartville jig pack tool
- Replies: 2
- Forum: User Announcements
A
I Got a New Shop Fixture *Pic*

Not woodworking but sure a nice "fixture" to have in the shop. Now I just have to build a door, or hang a sheet/blanket/etc.
- Alan in Little Washington
- Thread
- May 30, 2006
- fixture pic shop
- Replies: 18
- Forum: General Woodworking
Shop Made Horizontal Mortise/Tenon Fixture

A quick and easy to build fixture from Classic Joints With Power Tools by Yeung Chan, ISBN 1-57990-279-0. I started modifying the router mounting board to attach it to the fixture body with threaded rod for height adjustments, but found that Yeungs method of clamping it in the vice works just...
- Ken Massingale
- Thread
- Jan 9, 2006
- fixture horizontal made mortise or tenon shop
- Replies: 7
- Forum: General Woodworking