finally

  1. cskipper

    Charlie's Angel - finally finished!

    Well, I finally finished Charlie's Angel. It is officially the first intarsia project that I have completed (have several stuck in the process).
  2. WoodWrangler

    Finally Oscillating!

    A while ago I sold my Ridgid Oscillating Spindle Sander to an NCWW member (by the way, who was that ... I forgot ... send me a PM, I found a piece to it). I should have never done that ... I've needed it ever since! Well, finally yesterday I was up at The Woodworking Source and mentioned...
  3. W

    It's Finally Here!

    I finally got to pick up my new lathe.A Jet 16/42 , 2 hp in a nice shade of White.I sold my Woodfast back in late September and had this sitting at Klingspor since the October Woodworking Show.Between working 7 days a week and the total collapse of 4 major appliances in early November that wiped...
  4. S

    It’s finally completed

    I started working on this clock on and off since December 29, 2007. The clock is made out of Hackle berry. A friend gave me 20, 16 foot strips he found in his grandfathers Virginia barn. He thinks the wood was in the barn for over 30 years. The trim is from mahogany flooring. I resawed it...
  5. adowden

    Cherry buffet - finally finished!!!

    I finally finished the cherry buffet after more than 350 hrs. Here is a picture of the final piece: The top was some beautiful figured cherry: This design was based on a Garrett Hack huntboard in Fine Woodworking...
  6. P

    Lurker, finally decided to register...

    Like the title says, I've been lurking for a while, and figured I'd register. I've been turning wood and stone for a little over a year in a small 13 X 13 lathe room I set up at the end of 2008. This is a great site with quite a few resources. Hopefully I'll be able to expand my woodworking...
  7. MrAudio815

    Book Shelf....Some flat work Finally

    Hey Everyone, Remember when I made the cabinet for the wall out of MDF with a Hardboard backing. Welp I converted it into a Bookshelf and added Cherry trim. The top/front piece is one solid piece. Comments/opinions welcome, Good or Bad~! :gar-Bi
  8. Hook

    Finally getting back at it

    Have had almost no motivation to do any scrolling for awhile, decided to sit in front of the saw after getting some of the latest issues of SSW & C and digging through the 300 Christian SS patterns book. I realize some of these still need to be sanded:
  9. sawman101

    Finally goterdone

    View image in gallery Sucess at last. The third try was the charm. I downloaded some more photos of some of my latest projects--I checked, they're really there this time.
  10. crokett

    I Can Finally Pull Power To The Shop!

    The new panel is in. I programmed 4 hours, it took 4.5 included failing the first inspection. I got dinged on grounding issues. The range is 220 but is 2 hots and a bare ground. Inspector said that bare ground is now considered a neutral so I had to tape as much of it as I could and extend it...
  11. mbolt512

    Finally finished my first furniture project!

    OK guys, Here it is, my first furniture project. Let me start by saying nearly everthing involved with this project was a first for me from the design to the type of finish, so go easy on me. (As you can see from the pics LOML wasted no time bringing in the girl's stuff) Double bed/crib made...
  12. boxxmaker

    A few bowls I finally finished

    The top one is Ambrosia maple with a walnut foot,14 x 9" and the other one is maple burl 11 X 3" . Both are finished with my own danish oil mixture after sanding to 800 grit,then let dry for about two weeks then sanded again with 0000 steal wool and more 800 grit,then buffed with tripoli,then a...
  13. benwise

    Finally finished! walnut dining room table

    Thanks for all your advice during the project! Methinks I would have never finished without my friends at ncwoodworkers! the specs: 103" Long x 46" wide finished with BLO and waterlox Walnut salvaged from a friends yard after a lightning storm; to the sawmill and then in the attic for a...
  14. SteveCogs

    Finally finished a project

    Just a small table to put beside the back sliding doors. It's red oak with rock hard table top finish as I can see my LOML storing her watering can and wet yard gloves on it. She asked for a shelf but... this is what came out the other side of 3 months work/play in the shop.:gar-La; I figure I...
  15. B

    Toddler Bed Finished - Finally!

    This is my first "real" woodworking project. I made this for my girlfriendls three year old daughter. It's made out of poplar and has been stained (per the boss's orders) using General Finishe’s "Candlelight". This was intended to be a scaled down sleigh bed. This project was full...
  16. PChristy

    Finally a pic of the BOW bottle stopper(update)

    I tried to update the other thread that I started but couldn't find where you could edit the title - This is a couple of the BOW stoppers that I turned the one that is assembled is the one that stopped about a 32nd before being tight against the bottom - it has CA glue in it This is the...
    • PChristy
    • Thread
    • bottle bow finally pic stopper stopperupdate
    • Replies: 4
    • Forum: Woodturning
  17. Mark Stewart

    Finally a green turned bowl I am proud of

    Well This is what I call my first real sucess on the lathe with a green bowl blank. I got this lovely hunk of tree at the picnic, I got mi Ci0 and Ci1 in the mail monday. So its Wensday and here is the end result. It has a few problems but I am happy with it anyway. Thanks For looking. Mark
  18. WoodWrangler

    Maloof-style Rocker Finally Finished

    FINALLY! The day has arrived when this rocking chair is moving out of my shop and into my office (it’s temporary home). This has been a weekend project for sometime now and has sat in my shop while other projects took hole. But finally I got around to finishing it and the results are AWESOME...
  19. B

    Finally Used my Lathe - First Bowl turned today

    I bought my wife a lathe about 6 years ago with the hope that she might want to try turning. She decided that it was not for her pretty quickly and the lathe just sat there. I had not turned anything for about 40 years (since wood shop in junior high) until today when I put a bowl blank (green...
  20. Canuck

    Drillpress Gloat (Finally!) + Table

    Hi All! A little bit of background on my new drillpress acquisition. Awhile ago, I solicited input from you all here as to whether the Steel City 17” drillpress should win over the Jet 17” Weighing the features between the two, I decided upon the Steel City. At the time they were offering an...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top