circle

  1. NCGrimbo

    Balancing a circle of wood.

    My brother and I are working on a prize wheel. I cut the circle out of some left over funiture grade plywood using a circle jig and a router. The circle came out perfect with one problem. When it's mounted vertically and spun, it always stops at the same point due to the weight being uneven...
  2. Shamrock

    How do you shape the edge of a circle?

    I'm trying to avoid the tearout associated with routing against the grain as you rotate the circle counter clockwise. (I'm shaping the edge of a 20" circlular table top with a bearing guided round over bit on a router table) I've had luck in the past with dividing the circle into 4 parts and...
  3. Deep Hollowing Circle Cutter 2

    Deep Hollowing Circle Cutter 2

    • Nate Davey
    • Media item
    • 2 circle cutter deep hollowing
    • Comments: 0
    • Category: Member Galleries
  4. Deep Hollowing Circle Cutter

    Deep Hollowing Circle Cutter

    • Nate Davey
    • Media item
    • circle cutter deep hollowing
    • Comments: 0
    • Category: Member Galleries
  5. Simplest possible circle jig

    Simplest possible circle jig

    I built this to determine if the MLCS Marvel circle jig is really as bad as it seemed. It is.
    • merrill77
    • Media item
    • circle jig router
    • Comments: 0
    • Category: Member Galleries
  6. circle jig FAIL

    circle jig FAIL

    1st attempt at routing a circle with the MLCS Marvel and jig
    • merrill77
    • Media item
    • circle jig marvel mlcs router
    • Comments: 0
    • Category: Member Galleries
  7. timf67

    Carter Circle Cutting Jig - I just couldn't resist!

    I know, I know, there are many ways to cut a circle in wood without buying some fancy jig, but I just couldn't resist this one: I am a perfectionist, an I want ROUND bowl blanks for turning :gar-Bi. As Bas would say, I didn't need it, I just wanted it! Oh, and the bandsaw holding it is...
  8. Rob

    Circle template

    I've been hours hunting all over the web for this. I saw it at Bob's (WoodArtz) and would like one. It's a clear plastic circle template, has a center hole, various circle sizes so you can set it on a piece of wood and see how large a circle you can turn. Anyone know where I can get one...
    • Rob
    • Thread
    • circle template
    • Replies: 5
    • Forum: Woodturning
  9. johnpipe108

    RT circle jig solves template dilemma

    I needed to upgrade my router mounting plate to accept removable center inserts, as I bought a slot-cutter which wont fit the original 1-inch center hole. My dilemma was how to make a 4 inch circular template to use with a PC guide. After a bit of brainstorming, I came up with this jig...
  10. Splinter

    Router Circle Jig & Fence System - Review

    I purchased the Practical Technologies Multi-Purpose Base Plate & Circle Router Jig System, Fence ( http://www.practical-technologies.com/id15.html ) a couple of years ago. I have used it several times to route holes and have used it a few times with the fence. As stated on their web site it is...
    • Splinter
    • Thread
    • circle fence jig review router system
    • Replies: 0
    • Forum: Reviews
  11. R

    Band Saw Circle Jig

    I built a "zero clearance" table for my bandsaw, and incorporated a scale on the top to use as the basis for a circle cutting jig. To use the jig, I had a base with a brad through it, to which I attached the stock I was going to cut. I would insert the brad point in a hole on the corresponding...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top