aluminum

  1. rcflyer23

    Question on protecting Aluminum

    I am in the middle of a saw restoration and and was looking at the aluminum badge on the front that has the bevel angle screen printed on it and realized that the original owner never removed the thin protective layer however it's yellowed over the years and I started removing it but I would...
  2. J

    Aluminum miter slot runners

    I ordered a couple pieces of 6063, 3/8" X 3/4" aluminum bars from ENCO (use-enco.com.) They are exactly 0.750" wide, and fit my saws miters slots "like a glove." But they only come in 24" lengths. Enco item # 240-2401. Enco also has dial indicators and points sets on sale in current sales flyer...
  3. zapdafish

    countersinks and aluminum

    How bad would it be to use something like this on a piece of aluminum? I need a shorten a piece of miter bar stock and will need to drill my own hole in order to fasten it down.
  4. mkepke

    Where to buy aluminum plate in SE Wake ?

    Picked up a RAS from Sully (Jay), but it's missing one of the lower leaf guards. I think I should be able to fabricate a replacement from aluminum since I can copy the one I have. Does anyone have a source for cheap 1/8"-3/16" thick aluminum plate in SE Wake county ? Somebody with a pile of...
  5. mbeach

    aluminum pen - how to?

    anyone ever made a solid aluminum pen on a wood lathe? A friend wants me to make him one. Thanks Michael
  6. D

    T-Slot Aluminum

    I have some T-slot aluminum that I need to get cut into lengths for an application I have in mind. Does anyone know of a place where I can get that done, preferably in or very near Lincolnton, that won't charge me an arm and a leg.:eek: This is very similar to the profile of the material I...
  7. D

    Bosch Aluminum Framing

    I've managed to acquire a decent amount of this: http://www13.boschrexroth-us.com/Framing_Shop/Product/Default.aspx?units=1 given to me in exchange for a little "elbow grease" to take it apart.:wink_smil I've also got the Bosch/Rexroth catalog that lists all their really expensive :eek...
  8. AlexL

    Aluminum & Walnut Celtic Knot

    Hi everyone, I haven't been around in a while I've been really busy since the story came out in the newspaper. I wanted to show some of my newer pens. This is a european in big leaf maple burl. The celtic knot is walnut laminated between two thin strips of aluminum. Th finish is ca. This is...
    • AlexL
    • Thread
    • aluminum celtic celtic knot knot walnut
    • Replies: 24
    • Forum: Woodturning
  9. J

    Aluminum Foil and Rust

    After last weeks monsoon, my jointer had a faint hint of rust on the beds. Remembering that recently I had seen a tip to use aluminum foil to remove rust, I tried it- It Worked! Just wad up the aluminum foil and use as a scrubber on the rust. Cleans as well a steel wool. After cleaning, rub the...
  10. Splitter Installed

    Splitter Installed

    Splitter connects to guard post with existing bolt and fender washer.
    • KC7CN
    • Media item
    • aluminum splitter
    • Comments: 0
    • Album: PowerMatic 64A Table Saw - Shop Made Accessories
  11. Guard Mounting Bolt

    Guard Mounting Bolt

    • KC7CN
    • Media item
    • aluminum splitter
    • Comments: 0
    • Album: PowerMatic 64A Table Saw - Shop Made Accessories
  12. Aluminum Splitter

    Aluminum Splitter

    The small right-angle 'stop' sits next to the guard mounting post. It prevents the splitter from contacting the saw blade.
    • KC7CN
    • Media item
    • aluminum spliter
    • Comments: 0
    • Album: PowerMatic 64A Table Saw - Shop Made Accessories
  13. Aluminum Splitter

    Aluminum Splitter

    Splitter is made from 1/8'' right-angle Aluminum. The table saw guard bolt is used to secure the splitter. The bolt goes through the slot; the hole is not used.
    • KC7CN
    • Media item
    • aluminum splitter
    • Comments: 0
    • Album: PowerMatic 64A Table Saw - Shop Made Accessories
  14. Aluminum Splitter

    Aluminum Splitter

    PowerMatic 64A shop-made splitter mounts to table saw guard bolt.
    • KC7CN
    • Media item
    • aluminum clearance insert splitter zc zero
    • Comments: 0
    • Album: PowerMatic 64A Table Saw - Shop Made Accessories
  15. Eaglesc

    Aluminum X-wave

    This is the next step in the evolution of the "wave" design. Aluminum ebony and dyed veneers. I don't know when I will summon up the courage to drill mill and turn this one. I just like to look at it right now.
  16. Ken Massingale

    Extruded Aluminum For Jigs, etc.

    Lots of profiles at good prices. http://stores.ebay.com/8020-Inc-Garage-Sale_W0QQcolZ4QQdirZ1QQdptZ0QQfcpgZ15QQfgtpZ1QQfhpgZ15QQftidZ2QQpZ15QQtZkm ken

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top