Search results

  1. Scott Kuykendall

    Rigid Spindle sander?

    Had mine for over eight years and love it, it gets the most use of any sander in the shop. Wouldn't think twice of buying it again. Scott
  2. Scott Kuykendall

    Moving my shop

    I would use PODS like Mark said. They are very low to the ground (about3- 4") and what I did was to make a ramp out of plywood and blocking and then the tools with mobile bases I just rolled them in. I used my lumber stash to fit around the machines to keep them in place. The nice thing about...
  3. Scott Kuykendall

    Thinking about selling my shop

    I don't know about the area your in but you might want to try to make some simple children's items and try selling them, even on the side of the road,some where else if you don't have a lot of traffic by your house. I built some kids size outdoor furniture out of cheap pine and put them in front...
  4. Scott Kuykendall

    Help getting the broken roll pins (on the Delta BS) out

    -What model saw do you have? I looked at a manual on Delta's web site and looked at the 28-206 or 28-276. Are they the two pins that hold the upper arm to the base, they show four pins two on each side. If that is them the best way is going to be drilling a small hole (1/8") through the bottom...
  5. Scott Kuykendall

    What wood to use for picnic table

    Thanks everyone for the tips. Scott http://www.facebook.com/pages/Scotts-Woodworks/307823195931463
  6. Scott Kuykendall

    What wood to use for picnic table

    That's what my plan is to help him build it. I don't think its right to charge a neighbor plus with them helping if there wife doesn't like something about it they get to take the blame lol. Its not brain surgery to make a picnic table and I think that it better to work with them not for them...
  7. Scott Kuykendall

    What wood to use for picnic table

    My neighbor has asked me to build a picnic table for him and I am trying to find out what is the best type of wood to use without breaking the bank. I thought about using Cypress but can't find any 2X lumber around Spartanburg SC area. Does anyone know of a source for 2X4 & 2X6 lumber that would...
  8. Scott Kuykendall

    Turning Acrylic Pens

    After you get the blank roughed out you can use your skew laying flat on it's side on the tool rest and use it as a scraper taking light passes till you get the blank smooth. I can get my blanks smooth enough to just needing wet sanding with Micro Mesh. Scott...
  9. Scott Kuykendall

    Who Am I

    I am a 49 yr old self taught woodworker after becoming disabled due to a Semi truck accident in 1989. I have started making pens and other round things lately since they are lighter and easier to work with the the bigger projects I have done in the past. Scott Inman SC
  10. Scott Kuykendall

    Water heater leak question

    The pressure valve do go bad and are easy to replace. Some times by just releasing some water out the valve will flush a piece of junk that's on the seal causing it ti leak .You will need to turn off the water to the water heater and drain the water out of the tank so its below where the valve...
  11. Scott Kuykendall

    Plans Needed

    Here is a site with a drawing for a fly tying box http://www.itow.com/amago/b-streams/equipment/equipment2-2.html Scott
  12. Scott Kuykendall

    Red Flyer Wagon Plans???

    Woodcraft Magazine had a set of plans in issue #23 from June/ July 2008. http://www.woodcraft.com/Images/family/web20753big.jpg If you don't have access to that send me a email. Scott kuykendall63@gmail.com
  13. Scott Kuykendall

    purchased Rockler baby cradle plans...

    I made this one 12 years ago out of Red Oak. Scott
  14. Scott Kuykendall

    Bookcase/Dollhouse: Project Completed

    I made this one for my daughter about 9 years ago from a picture my wife had from a magazine. Looks like the same style and color lol. Scott
  15. Scott Kuykendall

    Hardwood Source Charlotte to Spartanburg Area

    I was wondering if any one knows of some where that sells small Qty of hardwood between Charlotte Airport and Spartanburg. I have to take the Family to the airport Thur and need a a about 10 bf of 5/4 Ash and didn't know if there is a place along my route. I e-mailed Advantage Lumber in Grover...
    • Scott Kuykendall
    • Thread
    • area charlotte hardwood source spartanburg
    • Replies: 5
    • Forum: Wood
  16. Scott Kuykendall

    How to Prep some Birch Wood

    The guy next door had a Birch tree cut down so I grabbed some of the biggest Dia. stuff there was. Its from 9" to 7" around and cut to 3 feet long. I am just starting out turning and have done some pens and Bottle Stoppers on my Rickon Mini. I sealed the ends with Anchor Seal right after they...
  17. Scott Kuykendall

    UPDATE: Scroller pattern Help please

    Re: Scroller pattern Help please Here is a stencil maker but the lettering is not very fancy but it might help you get started. http://woodgears.ca/stencil/index.html Scott
  18. Scott Kuykendall

    Looking for plans.

    Here is a few plans. http://www.mimf.com/archives/thickness_sander2.htm http://www.rockslide.org/drum%20sander.html http://www.rockslide.org/Images/drum_sander.pdf Scott
  19. Scott Kuykendall

    Assistance Please!

    They don't show cypress on there web site but if you call them if they don't have it they will know where to get it, here is there web site http://www.reellumber.com/index.htm. They have to locations on in Anaheim and another in Riverside. Boy do I miss shopping their, its like a kid in one big...
  20. Scott Kuykendall

    3/16" Brass rod around Raleigh

    Lowe's has some sizes, might want to check. Its with the steel in the hardware section. Scott

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top