Search results

  1. L

    Edge gluing

    I do have a Helical head on joiner and planner
  2. L

    Edge gluing

    If I get you right "out" board would have to run thru the planer reversed from the" In" board.
  3. L

    Edge gluing

  4. L

    Edge gluing

    Not sure I understand. I meant the two edges I’m running thru joiner at the same time will be the two edges glued together. Just not sure how to turn the edges. Like book pages or sides reversed.
  5. L

    Edge gluing

    Several years ago I saw an article that explained if you ran two boards at the same time on edge thru the jointer they would match perfect on the edge when gluing together. I guess that was because a jointer can be off a small amount off even when the fence is square. What I don't remember is...
  6. L

    Mortise and Tenon

    I have purchased at Festool Domino 700 (large size) and wondered if anyone used the larger domino in place of mortise and tenon joinery? I have a mortise and was thinking of selling it using the Festool.
  7. L

    Table saw

    I want to know what must woodworkers do when setting up the rip fence. Should the fence be completely square to the blade and miter track or is it better to set the far end a 32nd or so opened. I recently had a kick back incident that was not pleasant.
  8. L

    Inlay

    I purchased some templates to do an inlay on a table. I also got the guide and router bit for the inlay. I cut out the design with the 1/8 spiral bit and wasn't sure how to clean out the cut out. I assumed not to try that with an 1/8th bit and guessed you would use a larger bit and do it by...
  9. L

    Finish mixture

    I have some "Master Blend" 100% Tung Oil which has a finish formula printed on the label. It is one part Turpentine, one part varnish, and two parts Tung oil. I would like to add some Trans Tint dye. Anyone familiar with doing this I would like some advice.
  10. L

    Finishing mistake

    I have used two coats of thinned Rockhard this past weekend. That has helped the pore problem and I plan on doing a couple more thinned and a last coat of not thinned. I don't think I will need to take it back to bare wood. I appreciate all the good advice and I have purchased Aqua Coat and...
  11. L

    Finishing mistake

    Just brushing in this case and I do wipe when the product suggest it can be wiped
  12. L

    Finishing mistake

    Very sorry I took that the wrong way. Please accept my apology
  13. L

    Finishing mistake

    Yes I sanded with 320 grit lightly as not sand thru to the stain.
  14. L

    Finishing mistake

    Just why is that a stupid question? If I had to respond that to a question a person had I would just pass.
  15. L

    Finishing mistake

    I have built a Library Table out of quarter sawn white oak and made a bad finishing mistake. I did not use filler and have finished with three coats of Rockhard Table Top Varnish and the grain pores are visible. Do I have to sand off to bare wood and start over or is there something I can do...
  16. L

    wipe on urethane

    Has anyone tried wiping on Behlen Rockhard Table top Urethane. I have other varnishes and seem to get that smoother than brushing.
  17. L

    woodworkimng screws

    I know I am using the wrong wood screws in my work. What is the best to use and where to purchase.
  18. L

    Painted Headboard

    I am building a headboard for my granddaughter and would be interested in finding some one to paint it white. The exact tint to be decided later. I should have it finished (weekend worker) sometime in April.
  19. L

    De-waxed shellac

    I have a cherry bookcase to finish and like the look of Waterlox on cherry. I am thinking to cut down on blotching to use one pound cut de-wax shellac first and than Waterlox. Will this process effect the look of the normal Waterlox appearance. I am going to test on a piece of scrap but this...
  20. L

    PVC boards

    I have a project that I want to use (I think that is what it is) PVC boards that is one inch thick. They are smooth on one side and a small wood grain on the other. Can I run those thru my thickness planer with dulling or damaging my blades? I only have three pieces six feet long and probably...

Our Sponsors

LATEST FOR SALE LISTINGS

Top