Search results

  1. LeftyTom

    DIY Canopy Replacement

    The wind got the best of a 4yr old canopy last year. I dusted off my geometry skills, and ordered all parts from Amazon. I found UV- and water-resistant fabric in a 5ft by 50ft roll, so I have some left for another panel. I used "tarp repair clips" instead of grommets, in case I need to move...
  2. LeftyTom

    Brax Corner Clamps

    https://braxhardware.com/products/corner-clamps?fbclid=IwAR38Ii3QpPxL8AxEpoWZL65ofmnajZ1gfXbltCDAvK_tmsFQ1K6Abr-dn_c What is the collective wisdom on these?
  3. LeftyTom

    Birthday Gift

    Carla wanted to get me this for birthday. It was backordered, and Klingspor sent her the "shipped" email Tuesday DEC15. It arrived Wednesday morning DEC16.
  4. LeftyTom

    Working On End Tables

    I am working on a pair Arts and Crafts style end tables. I have the legs, shelves, and stringers cut. The narrower sides have 3 slats each, 3/8" thick. I have milled the ash I have down for all the parts. I laminated the ash to get a 3" thickness, which I think I will simply leave with the...
  5. LeftyTom

    Lost A Screw, Buy A Blade

    I seem to have lost the iron to chip breaker cap screw on a Fulton plane. The plane body is stamped 3709 on the side, and 301 under the frog. (The brazing on the side does not affect the sole). While the parts are soaking in Evaporust, I can peruse a new blade, as I see light between the...
  6. LeftyTom

    Fulton Work

    I got a bit of planing done Monday morning. No paper thin ribbons, but I am getting ribbons.
  7. LeftyTom

    Smoke/Carbon Monoxide Detector Recommendations?

    A Duke Energy transformer up the road went south last week. When power was restored an hour later, the Firex smoke detector in the basement went bonkers, continuously sounding the alarm. This alarm is interconnected with a second alarm upstairs, which was going off also. The upstairs detector...
  8. LeftyTom

    Spindle Or Hand Sand?

    I am working on a table with curved skirts (no, I am not wearing the skirts). After running the pieces by the spindle sander, I still have a few bumps to flatten (may not be noticeable in the pics). Would you touchup using the spindle sander or sandpaper attached to a curved piece of scrap?
  9. LeftyTom

    Bandsaw Tire Check

    I was cutting some 9" long 1/2" thick alder on the bandsaw, using a 3/8" blade. Almost through the second piece, when I smelled hot rubber. Shutdown the bandsaw and saw this The funky color on the blade is "blade lube". I slipped the tire back on, readjusted the upper wheel so the blade...
  10. LeftyTom

    HNPD, Part 2

    I scored myself a Sargent 409, to go with the Sargent 409C. Now I can argue with myself whether a corrugated sole is better.
  11. LeftyTom

    HNPD

    Happy New Plane Day! I snagged this off Ebay for $35. It was listed as a Sargent 409C. The adjustment knob has right-hand threads. The tote was a bit lose, but a few turns of the screwdriver took care of that. The iron is dull, but I have a diamond sharpening kit (325, 600, & 1000...
  12. LeftyTom

    Sanding Shoe For Flattening Panels?

    Have anyone tried a belt sander with a sanding shoe for flattening glued-up panels? I have 4 panels that need a tad of flattening, 1/100 to 7/100. My belt sander is a Craftsman 3"x 18", which is 20 years old, so I suspect a sanding shoe is not available. So I may be adding a new belt sander...
  13. LeftyTom

    Need Switch Cover For Delta 10"Drill Press

    Where can a fellow get one of these? The 2 plastic flanges on the back broke earlier this week.
  14. LeftyTom

    Grizzly $40 Mystery Box

    I took the plunge on a Mystery Box, which arrived today. 9-piece hex key set My Grip DIY custom grip Pair of bright yellow shooting glasses and hard case Dead blow hammer 2" tube fitting brush 5oz oil can Two Pony 2 1/2" C clamps 2 gun packs cleaning patches Red ammo box Pack of 10 hand scrubs...
  15. LeftyTom

    Mixing Paint With Anti-Skid

    Anyone have experience with mixing your own anti-skid paint for exterior use? I am using is Homax Anti-Skid Paint Additive; Perlite and Crystalline Silica, so I will be using a mask. Should I use all the paint mixture, or does it store well/stir up later OK? Amazon had a one pound bag for $9...
  16. LeftyTom

    Where To Buy: Blo Mold Bulb Holder & Power Cord

    My brother brought me 9 Blo Mold figures to go with my yard Christmas decorations. 4 are missing the C7 (nightlight) bulb holders (1' openings in the Blo Molds). One is missing the holder for a 60W bulb. A quick search finds them at sites for $11 a pop, and up. Have any of ye merry gentlemen...
  17. LeftyTom

    Picking A New Riding Mower

    After 16 years of service, my Husqvarna 42" mower has bitten the dust; the motor is idling fine, but with an additional metal sound. :( New motor, you suggest? That will run over $1K, then there is the question of what else will fail. I was considering the Toro SW4200 or Cub Cadet RZT SX42...
  18. LeftyTom

    Upside To Polar Vortex

    I heard on NPR, from a learned fellow in Minnesota, that the frigid weather may help kill off the emerald ash borer. The cold snap may also help with a tick problem in Maine.
  19. LeftyTom

    Hncd!

    Happy New Caliper Day! Two previous digital calipers went kaput, so I decided to go old-school.
  20. LeftyTom

    Grilling Season Cart, Finished Pics

    Ash frame, white oak shelves (oak from Rick DiNardo). Just need some Titebond for the loose tendon joinery. The I will put 2" wheels under the legs.

Our Sponsors

LATEST FOR SALE LISTINGS

Top