Search results
-
Getting Rid of Sharp Corners
If you just want to " break" the sharp edge, I have found the Fast cap dual edge sander works very well with a couple of light passes with a fine grit sandpaper...- Canuck
- Post #3
- Forum: General Woodworking
-
Why...
Sorry bout that, Hank. My editor went berserk when I tried to add text to my 1st post,..... We are in the process of drawing up a plan for a media console for our own home. LOML cannot find a commercial option that will #1 fit the style she is looking for, #2 anything beyond veneer over...- Canuck
- Post #15
- Forum: General Woodworking
-
Why...
Two weeks ago I completed a small cabinet for a son in laws grandmother who was having trouble finding a cabinet that would suite/fit into a specific location in her home. I used 4/4 poplar and 1/4” and 3/4” plywood with dowel joinery. Next up is a- Canuck
- Post #9
- Forum: General Woodworking
-
Router bit slot cutters - can the 'blades' be stacked? (Update)
I purchased this inexpensive set is slot cutters a couple of years back and it has served me well. I too have found that today's 1/4" ply has shrunk to be more like 3/16" thick. This is the set of slot cutters I have been using when routing rails and stiles for panel doors...- Canuck
- Post #3
- Forum: Power Tools and Their Use
-
-
Cuts, gouges and Scrapes, Oh My
Yup! I don’t need a branding iron; I leave spots of DNA on almost every project!- Canuck
- Post #4
- Forum: General Woodworking
-
-
-
Bosch 12 inch Miter Saw
Yes. Got the Makita stand as well. (I purchased mine from Acme Tool and the stand was part of a Makita promo- same price.)- Canuck
- Post #4
- Forum: Power Tools and Their Use
-
Bosch 12 inch Miter Saw
I recently purchased a Makita 10" slider (model LS1019L) with soft start. Is performing very well for me! Wayne- Canuck
- Post #2
- Forum: Power Tools and Their Use
-
Finally Finished our Kitchen table
Very well done! The finish looks great. Wayne- Canuck
- Post #8
- Forum: General Woodworking
-
Preferred miter slot router bit?
Have you tried Toilet Flange bolts with your slot cutter? Is use these with Rockler to track..... https://www.lowes.com/pd/Oatey-Polished-Brass-Toilet-Hardware-Kit-For-Hercules/1000116161 (If the flange is a little too wide rot the to track I am using, I just come or grind a wee bit of of the...- Canuck
- Post #12
- Forum: Power Tools and Their Use
-
Making a Fence for Delta 14 Bandsaw
I have using Kreg bandsaw fence for a number of years on my Delta 14" bandsaw and it has served me well. Fits well and easy to install. https://www.amazon.com/KREG-KMS7200-Kreg-Bandsaw-Fence/dp/B0007VYL48 Wayne- Canuck
- Post #4
- Forum: "How To" Forum
-
Preferred miter slot router bit?
Purchased this one from Leigh Valley a few years back and it has performed pretty well. https://www.leevalley.com/en-us/shop/tools/power-tool-accessories/router-bits/65641-undercut-slotting-bit After hogging out the majority of material with a straight bit or dado stack, there isn't much...- Canuck
- Post #5
- Forum: Power Tools and Their Use
-
Happy Birthday Alan in Little Washington
All the Best on your special day, Alan!- Canuck
- Post #13
- Forum: User Announcements
-
Cabinet question
+1 or you'll end up with a gap in the middle where the two doors meet.- Canuck
- Post #6
- Forum: General Woodworking
-
2x4 Office Shelving
Fast cap sell a rounded (concave) sandpaper holder that I find helpful in breaking sharp edges. Called a Fast break...- Canuck
- Post #38
- Forum: Project Design
-
BS blade tracking hinge
I have a Delta 14” 28-275 and just took a picture of my spring tensioner and Bob is correct. The nut sits at the bottom of the spring on mine.- Canuck
- Post #26
- Forum: Power Tools and Their Use
-
Recent Turnings
All terrific! With Bill here, the middle one is quite awesome.- Canuck
- Post #5
- Forum: Woodturning
-
Our Sponsors
LATEST FOR SALE LISTINGS
-
-
-
-
For sale: Gently used Shaper Origin - $2000 OBO (pending sale)- Started by jrs
- Replies: 5
-
