Search results

  1. Jeremy Scuteri

    Floating Shelf with Shaper and Power Feeder

    I spent some time using the shaper with the power feeder that I installed back in February. (https://ncwoodworker.net/forums/index.php?threads/power-feeder-mounting-install.69273/) I'm making a floating shelf for a soundbar that will sit under a wall mounted TV. I'm really impressed with the...
  2. Jeremy Scuteri

    Hydraulic Lift Table Troubleshooting

    Back in January I picked up an electrically powered hydraulic lift table at an auction. It raises and lowers with foot-pedals that control a motor and solenoid down valve. Below is the lift table. It has been very nice to put the work at any height I want. Prevents me from bending over in...
  3. Jeremy Scuteri

    Cherry Headboard

    I set out to make a bed about 4.5 years ago after my wife asked for a simple headboard. I designed a bed in sketchup which took a while to do and started building it about 5 years ago. Then we moved and I built the new shop which really took a long time. My wife bought a headboard several...
  4. Jeremy Scuteri

    Black Walnut Floating Top End Table

    11 years ago I bought some black walnut for dirt cheap. Note the piece on the far right. I thought that was an interesting piece at the time, but never know what I would use it for. The bench is 60" long for reference. Some cleanup Crosscut on the slider Then off to the bandsaw Some...
  5. Jeremy Scuteri

    Power Feeder Mounting/Install

    I picked up this power feeder at an auction a while back, before the new house and the basement shop build, so this was a few years ago. I finally drilled and tapped the holes in the shaper table and put it in place. I went with 7/16-20 bolts, I could have used 1/2" instead, but I figured a...
  6. Jeremy Scuteri

    Phenolic Resin from Bruce

    I decided to make up some zero clearance inserts (ZCI) for my Grizzly table saw. I am using some phenolic resin that I got from @sawman101 (Bruce). I cut strips to width on the table saw, cut curves over sized on the bandsaw and used a flush trim bit on the router. Drilled a finger hole and...
  7. Jeremy Scuteri

    Made a Lacewood Shelf with my Daughter

    I asked my daughter if she wanted to make a shelf for her room together. I got out the dry erase board and suggested something like this: Right away, she rejected that design and sketched her own with 3 shelves and hooks at the bottom. Ok, well at least she knows what she wants! :) A few...
  8. Jeremy Scuteri

    Tool Wall

    I'm starting to take advantage of the empty wall space in the shop. I turned my workbench around so that the wall would be accessible by simply turning around. The large tool wall surface is drywall with a piece of OSB attached and painted white. The OSB was leftover from the shop floor...
  9. Jeremy Scuteri

    Table Saw Central

    I have had table saw outfeed support on my "To Do" list for quite some time. Naturally another table saw is the obvious choice for outfeed support. I went with a Grizzly table saw and I finally have everything in place. Here is the saw when it first arrived. I bribed some neighbor kids to...
  10. Jeremy Scuteri

    Grizzly G1023 Mods - Drilling Holes in Metal - Outfeed Support

    After some encouragement at the shop crawl, I mustered up the courage to drill some holes in cast iron. It wasn't nearly as bad as I expected. I started with a small hole (1/8") and then went to 1/4" then 3/8". The first hole was by far the hardest and most time consuming to drill. After...
  11. Jeremy Scuteri

    How to create a "Sub Album/Folder" in the Media Section

    I am trying to create an album for the pictures from the Shop Crawl. I found the location of the previous shop crawls (see picture below), but I can't figure out how to create a new folder/album. Any suggestions?
  12. Jeremy Scuteri

    Drill Press Cabinet

    I finally finished my Drill Press Cabinet. It was mostly based on the Woodsmith Shop design shown below: First the base was built using poplar and plywood. Next was a platform to go over the mobile base. Both pieces are on wheels. One of the modifications is a...
  13. Jeremy Scuteri

    Limit of 5 people in a "Conversation"?

    There seems to be a 5 person limit for PMs/Conversations. Is there a way to change that? I can't talk to all the Shop Crawl hosts in a single PM which has obvious ramifications. Also, how do you add more names to an existing PM/Conversation?
  14. Jeremy Scuteri

    NCWW Calendar

    How do I add an entry to the NCWW Calendar? This is what I see:
  15. Jeremy Scuteri

    Are you in the Triad area?

    Are you in the Triad Area? If you are, you should consider being one of the shops on the upcoming Shop Crawl. https://ncwoodworker.net/forums/index.php?threads/shop-crawl-it-is-time.67326/#post-626147 All responses should be posted in the linked thread above. I want to keep as much as...
  16. Jeremy Scuteri

    Triad SHOP CRAWL - August 17th 2019

    Some of the newer members may not be aware of this, but one of the really awesome things that we do at NCWW is the Shop Crawl. The idea is we find a handful of people willing to show NCWW members their shop, maybe 4-8 shops that are in reasonable proximity to each other would be typical. Lunch...
  17. Jeremy Scuteri

    Worksharp bevel not square - Only idiots read manuals

    Today at the Greensboro lunch I brought up how my Worksharp does not create a square bevel when using the built in "sharpening port" underneath the spinning disc. We talked about it some and a comment that "somebody has probably figured out a solution for that" was mentioned. I figured I might...
  18. Jeremy Scuteri

    2019 Raffle Results and Data

    We had the picnic and raffle drawing today. We met our goal of $10,000 with $10,315 in total sales. Thank you to everyone who bought tickets. Here are some fun facts about the raffle: - Two different people purchased over 100 tickets each. Thank you for your support! - Thirteen people...
  19. Jeremy Scuteri

    1 More Hour to Buy Online Tickets

    https://ncwoodworker.net/forums/index.php?ncww_raffletickets
  20. Jeremy Scuteri

    Online Raffle Ticket Sales End Tonight!

    Buy your tickets online while you still can. Online sales end tonight at approximately midnight. https://ncwoodworker.net/forums/index.php?ncww_raffletickets

Our Sponsors

LATEST FOR SALE LISTINGS

Top